Step: 1

Place Card:

Step: 2

Preheat your DRY iron to the wool setting.

Step: 3

Using the leftover white cardstock, fold and cut out to a 3-1/2” width.

Step: 4

Using your computer, type the guest’s name and print on white paper.

Step: 5

Cut out the text, and trim approximately 1/4” smaller than the cardstock. Adhere

Step: 6

the paper to the cardstock.

Step: 7

Print the palm leaf design and cut out the small leaf. Using as a stencil, trace

Step: 8

onto the green paper and cut out. Erase leftover pencil marks.

Step: 9

Apply the green leaf to the bottom right corner.

Step: 10

Cut a border using the hot pink paper that is 1/8 to 1/4” wide. Apply on top of

Step: 11

the green leaves.

Step: 12

Apply the hibiscus cut out on top.

Step: 13

Peel off a few of the rhinestuds and position as desired on the green leaf.

Step: 14

Lightly press each stud with the iron tip for 3 to 5 seconds.

Step: 15

Invitation:

Step: 16

Preheat your DRY iron to the wool setting.

Step: 17

Using your pencil and ruler, lightly mark 4-3/4 x 6-7/8” in one corner of the

Step: 18

white cardstock, and cut out. Save the rest for the menu and place setting card.

Step: 19

Using your computer, type the invitation and print on white paper.

Step: 20

Cut out the text, and trim approximately 1/4” smaller than the cardstock. Adhere

Step: 21

the paper to the cardstock. If you cut it slightly smaller than the cardstock, do

Step: 22

not worry about the seam. You will cover it up with the hot pink border.

Step: 23

Peel off the backing layer from the rhinestud design and lightly stick onto the

Step: 24

light pink cardstock. Remember that you will be peeling off the clear sheet, so

Step: 25

do not press too hard or it may be difficult to remove.

Step: 26

Press directly onto the clear sheet with the iron for 3 to 5 seconds. Work in

Step: 27

sections so that the entire design is covered. Cool completely, and gently peel

Step: 28

off the clear adhesive sheet. .Also, see the project tip.

Step: 29

Trim around the rhinestud design leaving a 1/4” border.

Step: 30

Print the palm leaf design and cut out. Using this as a stencil, trace onto the

Step: 31

green paper and cut out. Erase leftover pencil marks.

Step: 32

Using the two palm cut-outs, and the hibiscus, determine where you like to

Step: 33

position them, and apply the green leaves only.

Step: 34

Cut a border using the hot pink paper that is 1/8 to 1/4” wide. Apply on top of

Step: 35

the green leaves.

Step: 36

Apply the hibiscus cut out.

Step: 37

Menu:

Step: 38

Preheat your DRY iron to the wool setting.

Step: 39

Using your pencil and ruler, mark off the longest portion of the leftover white

Step: 40

cardstock and cut out. Should be approximately 7-1/4 x 12”

Step: 41

Using your computer, type the menu and print on white paper.

Step: 42

Cut out the text, and trim approximately 1/4” smaller than the cardstock. Adhere

Step: 43

the paper to the cardstock. If you cut it slightly smaller than the cardstock, do

Step: 44

not worry about the seam. You will cover it up with the hot pink border.

Step: 45

Peel off the backing layer from the rhinestud design and lightly stick onto the

Step: 46

light pink cardstock. Remember that you will be peeling off the clear sheet, so

Step: 47

do not press too hard or it may be difficult to remove.

Step: 48

Press directly onto the clear sheet with the iron for 3 to 5 seconds. Work in

Step: 49

sections so that the entire design is covered. Cool completely, and gently peel

Step: 50

off the clear adhesive sheet. .Also, see the project tip.

Step: 51

Trim around the rhinestud design leaving a 1/4” border.

Step: 52

Print the palm leaf design and cut out. Using as a stencil, trace onto the green

Step: 53

paper and cut out. Do two of the small leaves. Erase leftover pencil marks.

Step: 54

Using the three palm cut-outs, and the hibiscus, determine where you like to

Step: 55

position them, and apply the green leaves only.

Step: 56

Cut a border using the hot pink paper that is 1/8 to 1/4” wide. Apply on top of

Step: 57

the green leaves.

Step: 58

Apply the hibiscus cut out on top.

Step: 59

Take Out Box:

Step: 60

Preheat your DRY iron to the wool setting.

Step: 61

Carefully take apart the take-out box, creating a flat surface.

Step: 62

Peel off the backing layer from the rhinestud design and lightly stick onto the

Step: 63

box. Remember that you will be peeling off the clear sheet, so do not press too

Step: 64

hard or it may be difficult to remove.

Step: 65

Press directly onto the clear sheet with the iron for 2 to 4 seconds. Work in

Step: 75

sections so that the entire design is covered. Cool completely, and gently peel

Step: 76

off the clear adhesive sheet. Also, see the project tip.

Step: 66

Reassemble box.