Sapphyra Necklace
Add to Favorites Print

Sapphyra Necklace

Techniques To Know: Form a Loop and Jump Rings

Uses Recycled Items: No
 
 
 
 
Get exclusive offers about this product and more!
 
 

Material List

  • Crystazzi® 2-Strand Floral Square Connector – Crystal (10 Pk.)
  • Crystazzi® Rounds, 8mm – Lilac (2 Pk.)
  • Crystazzi® Rounds, 8mm – Indicolite (2 Pk.)
  • Eye Pins – Silver-plated (2 Pk)
  • Rhinestone Chandelier – Silver-plated (4 Pk.)
  • Teardrop Chandelier – Silver-plated (8 Pk.)
  • Rhinestone Magnetic Clasp – Silver-plated (1 Pk.)
  • Open Jump Rings, 4mm – Silver-plated (5 Pk.)
  • Round Nose Pliers
  • Needle Nose Pliers
  • Wire Cutters
 

Project Instructions

Step 1 Make (14) Indicolite round links and (18) lilac round links.

Step 2 Attach each beaded link to an open chandelier connector. One end of a beaded link attaches to the inside loop of the connector and the other end attaches to the bottom center loop of the connector.

Step 3 Trim the lilac connector loops as follows: Trim the right and left loops off of eight lilac chandeliers so they have only a single center loop at the bottom. These are called A-1. Trim left loop off of eight lilac chandeliers so they have only a center loop and a right loop at the bottom. These are called A-2. Do not remove any bottom loops on two lilac chandeliers. These are called A-3.

Step 4 Trim the Indicolite connector loops as follows: Trim ten Indicolite chandeliers to have only a single center loop at the bottom. These are called B-1. Trim two Indicolite chandeliers to have a center loop and one side loop at the bottom. These are called B-2. Keep two Indicolite chandeliers with three bottom loops. These are called B-3.

Step 5 Trim the crystal chandeliers loops as follows: Trim two crystal chandeliers to have one loop at the far end of the bottom. These are called C-1. Trim two crystal chandeliers to have only a single center loop at the bottom. These are called C-2. Trim two crystal chandeliers to have a center loop and one side loop at the bottom. These are called C-3. Keep two crystal chandeliers with three loops at the bottom. These are called C-4.

Step 6 Link the 4mm jump rings together into sets of two.

Step 7 Use a 4mm jump ring to link one end of the magnetic clasp to the top loop of A-1. Connect a set of jump rings to the bottom loop of A-1 and connect to a flower connector.

Step 8 Attach a set of jump rings to the other end of the flower connector and connect to B-1. Connect a set of jump rings to the bottom loop of B-1 and connect to a flower connector.

Step 9 Repeat connecting A-1 to the flower connector. Then connect to a B-2. The additional loop should be facing downward. Connect a flower connector to the center bottom loop on B-2. Attach A-2 to the other end of the flower connector. The additional loop on A-2 should be facing downward.

Step 10 Connect a flower connector to the center bottom loop on A-2.

Step 11 Repeat Steps 7-9. Attach center bottom loop of A-2 to the other end of the flower connector from Step 10.

Step 12 Connect a set of jump rings to C-2. Connect the bottom loop of C-2 to a flower connector. Attach the connector to the top loop of A-1. Attach the bottom loop of A-1 to a flower connector. Attach the connector to the top loop of A-2 (the extra loop should face towards the right). Attach a flower connector to the bottom center loop of A-2. Attach a B-1 to the other end of the flower connector. Attach the other end of B-1 to a flower connector.

Step 13 Attach A-1 to the left loop of a flower connector. Attach the other end of A-1 to the left loop of a flower connector. Attach a B-1 to the bottom loop of the flower connector.

Step 14 Repeat Step 12. (The extra loop of A-2 should face towards the left.) Then attach A-1 to the right loop of the flower connector from Step 13.

Step 15 Link the top loop of a B-1 to the bottom loop of the flower connector from Step 10. Link the bottom loop of B-1 to a flower connector. Connect the flower connector to the top loop of a B-1. Link the bottom loop of B-1 to a flower connector. Connect the flower connector to the top loop of a B-1. Link the bottom loop of B-1 to the top loop of the flower connector from Step 13.

Step 16 Link the top loop of a B-3 to extra loop of the B-2 from Step 9. Connect the left loop of the B-3 to the right loop of the first flower connector in Step 12. Attach the top loop of a C-4 to the bottom right loop of the B-3.

Step 17 Attach a B-1 to the left bottom loop of the C-4 in the previous Step. Attach a flower connector to the B-1. Link the left loop of the flower connector to the inside right loop of the A-2 from Step 12. Attach a C-3 to the bottom loop of the flower connector.

Step 18 Attach a flower connector to the center bottom loop of the C-3 from the previous step.

Step 19 Link an A-2 to the top loop of the A-2 from Step 9 (at the center of the necklace). Use a single jump ring to link the left loop of the A-2 to the right bottom loop of the C-4 from Step 16. Link a flower connector to the center bottom loop of the A-2. Attach an A-3 to the bottom loop of the flower connector. Link a flower connector to the bottom left loop of the A-3 to the bottom right loop of the C-3 from Step 17.

Step 20 Link a C-1 to the bottom loop of the A-2 from Step 9. Connect the only loop of C-1 to the right loop of the flower connector from Step 19.

Step 21 Link the A-3 from Step 19 to the left loop of the flower connector from the center section of the necklace (Step 15).

Step 22 Repeat Steps 16-21 for the opposite side of the necklace. Remember to reverse the direction of the connector loops to ensure the pieces connect to the center of the necklace.