Superstar Costume
Add to Favorites Print

Superstar Costume

What little girl under age 12 isn’t a fan of Hannah Montana? Put a smile on your child’s face by creating her own “Super Star” Halloween costume. Designed by Duncan
Craft Time: varies
Get exclusive offers about this product and more!

Material List

  • Tulip® 3D Fashion Paint™- Purple Slick® and Diamond Glitter®
  • Tulip® Soft Fabric Paint™- Platinum Metallic
  • Tulip® Fashion Glitter™- Pink Jewel, Purple Jewel and Multi Medium Crystal
  • Tulip® Fashion Glitter Bond™
  • Tulip® Sticky Fabric Stencils™- Everyday 4x4 and Edgy 4x8
  • Tulip® Fashion Form™
  • Aleene’s® Craft Adhesives™- FunCraft™ Foam Glue
  • Foam Sheet - Bright Pink
  • 2 T-Shirts- White and Pink
  • Knee Socks- White
  • Sunglasses
  • Scissors
  • Paper Towels
  • Low Tack Masking Tape
  • Mailing Tube
  • Plastic Wrap
  • Small Round Brush
  • Foam Plate
  • Scratch Paper
  • Pencil
  • Blow Dryer - Optional

Project Instructions

Step: 1

White Shirt:

Step: 2

Use scissors to cut off hem, sleeves and neck so shirt looks like a tank top.

Step: 3

Insert Fashion Form inside shirt. Squeeze a small puddle of Platinum Soft fabric paint onto foam plate. Add a few drops of water and use brush to thoroughly mix, adding more water as needed till paint is consistency of milk.

Step: 4

To create spattered look, fill brush with paint and flick across shirt. Continue to spatter filling brush with paint changing direction for interest. Let dry. Hint: Use a blow dryer to speed up dry time.

Step: 5

Use scissors to cut lighting bolts from stencil leaving a slight border around each. Follow package direction to apply stencil. Add pieces of low tack masking tape around edges of stencil to extend borders.

Step: 6

Squeeze a small puddle of Glitter Bond onto foil. Tap the flat end of wedged sponge into adhesive pouncing an even layer within stencil. Immediately pour an ample amount Pink Jewel Glitter within stencil design. Use finger to slightly press glitter into glue. Tap excess glitter onto scratch paper.

Step: 7

Position bolt stencils referring to photo and package directions for stencil. Tape around edges to extend border. Apply Glitter Bond and pour on Purple Jewel Glitter. Carefully remove stencil and reposition. Repeat step with remaining lightly bolts around guitar. Let dry.

Step: 8

Use a pencil to lightly draw on lettering where desired. Squeeze Purple 3-D paint along lines and while wet sprinkle Purple Jewel Glitter over paint. Let sit about 10 minutes and lightly pounce off excess.

Step: 9

When shirt is thoroughly dry, use and old stiff brush to brush off all excess glitter.

Step: 10

Use scissors to cut a 5” slit along left side at lower edge of shirt. Tie ends together forming a knot.

Step: 11

Pink Shirt:

Step: 12

Cut hem from sleeves and around bottom of shirt. Insert Fashion Form.

Step: 13

Remove star stencil from package. Position in place on shirt.

Step: 14

Apply Glitter Bond over stencil and pour on Multi Medium Crystal Glitter. Lightly press glitter with fingers then pounce off excess. Re-position stencil and repeat step continuing by adding stars around top and lower edge of shirt. Let dry.

Step: 15


Step: 16

Cut out pattern. Place on foam sheet using pencil to trace around design creating two. Cut out eyeholes.

Step: 17

Tape foam to paper. Fill in entire top of each shape with Diamond Glitter 3-D paint leaving a smooth even layer. Let dry.

Step: 18

Flip over and apply a bead of Fun Foam Glue around eyeholes. Let dry.

Step: 19

Press onto glasses adjusting to fit.

Step: 20


Step: 21

Cover mailing tubes with plastic wrap and tape to hold in place. Slide socks over tube.

Step: 22

Position star stencil in place. Sponge on a thin even coating of Glitter Bond within star and sprinkle on Pink Jewel Glitter. Repeat steps to complete both socks. When dry remove socks from tube. (Optional: cut removed hem from pink shirt in half to use as tie for socks).


Before applying adhesive have your glitter ready to pour. Place paper under garment when applying glitter so that any excess is not lost and can be returned to bottle for re-use