Woodland Friends Cardholder
Add to Favorites Print

Woodland Friends Cardholder

Turn a wooden plaque & box into a stylish place to keep all your holiday cards this season.
Craft Time: 60+ minutes
Uses Recycled Items: No
 
 
 
 
Get exclusive offers about this product and more!
 
 

Material List

  • CraftSmart Acrylics:
  • CS120 White
  • CS135 Holiday Red
  • CS140 Orange
  • CS145 Tan
  • CS147 Brown
  • CS153 Yellow
  • CS167 Spanish Olive
  • CS173 Pale Blue
  • CS191 Dark Grey
  • CS192 Black
  • CraftSmart Varnish CS300 Matte Varnish
  • 6” square wood plaque
  • 4¼” x 6” x 8½” wooden box
  • ¾” wash/glaze brush
  • #1 flat brush
  • #0 spotter brush
  • Water container
  • Palette or plastic plate
  • Paper towels
  • Black ultra-fine felt tip pen, LePen
  • 150-grit sandpaper
  • Brown paper bag
  • Wood glue
 

Project Instructions

Note: Allow paint to dry between colors, coats, and steps. Allow glue to dry

before next step.

1. Using wood glue, adhere wooden plaque to front of wooden box.

2. Sand cardholder smooth with 150-grit sandpaper and remove any dust

with damp paper towel.

3. Using piece of brown paper bag, sand cardholder smooth and remove any

dust with damp paper towel.

4. Mix Brown with water to consistency of milk. Moisten paper towel with

water and ring out to point that water is no longer dripping from towel, but

that towel is still thoroughly wet.

5. Dip wet towel in watered down Brown from step 4 and rub over cardholder

to stain all sides and bottom. Make sure stain is absorbed, but don’t rub so

hard that paper towel falls apart.

6. Allow to dry and sand smooth with brown paper bag. Remove any dust

with damp paper towel.

7. Repeat steps 5-6 until desired amount of stain is achieved.

8. Using ¾” wash/glaze flat brush, basecoat front of cardholder with 2:1 mix

of Pale Blue + White.

9. Copy pattern onto tracing paper and transfer to front with graphite transfer

paper underneath. Use stylus or ballpoint pen to transfer pattern lines.

10. Using #0 spotter brush, basecoat owl with 1:1 mix of Brown + White; owl’s

scarf, Holiday Red; star, Yellow; eyes and star’s stick, White; and feet and

beak, Orange.

 

11. Using # 1 shader brush, basecoat tree Spanish Olive; trunk, Brown; and

snow, White

12. Using #0 spotter brush, basecoat fox’s coat, top of head, and bottom of

tail with mix of Pumpkin + touch of Holiday Red; chest, face, and tip of tail

White; legs, Black; and bell with 2:1 mix of Dark Grey + White.

13. Using #1 shader brush, basecoat hedgehog’s face, hands, and feet with

1:2 mix of Tan + White; his coat, Brown; and his ornament, Holiday Red

with top of ornament Yellow.

14. Using #0 spotter brush, basecoat raccoon’s body and head with 2:1 mix of

Dark Grey + White; face, hands, and tail stripes, Black; muzzle and top of

eyes, White; and present, Spanish Olive + White 2: 1.

15. Using ¾” flat brush, basecoat snowy ground White.

16. Using handle end of large paintbrush, dot in White snowflakes.

17. Using black ultra-fine felt tip pen, outline woodland creatures, tree, ground,

and snowflakes. (See photo.)

18. Apply two coats of CraftSmart Matte Varnish, allowing to dry and sanding

with brown paper bag between coats.

Tips

When basecoating, add as many coats as needed to cover completely.

Craft Notes

Crafted for Michaels by Barbara Greve.