Home  >  Halloween Barrettes


Halloween Barrettes
enlargeenlarge

Halloween Barrettes

Add a special touch of Halloween fun to your child’s costume with this easy barrette.
Designed by Melissa Zonfrillo
  
Project #:
e05677
  
 
 Crafting Time: 30-45 Minutes
 Skill Level:
 1 being the easiest
 Crafters Rating:
  Review this project
  Add to My Michaels
  Printer friendly version
  Email to friend
 
  • For All Barrettes:
  • Scissors
  • Glue or Glue Gun
  • Candy Corn Barrette:
  • 3-inch Barrette
  • Horizon Group USA Yellow Candy Corn Ribbon
  • Horizon Group USA Yellow & Orange Striped Ribbon
  • Black and Orange Barrette:
  • 2-inch Barrette
  • Horizon Group USA Black & Orange Satin Dualities Ribbon
  • Horizon Group USA Black & White Polka Dot Grosgrain Ribbon
  • Trick or Treat Barrette:
  • 3-inch Barrette
  • Horizon Group USA Black & Orange Checkered Ribbon
  • Horizon Group USA Orange ‘Trick or Treat’ Ghost Ribbon
  • Black, White and Orange Barrettes:
  • 2-inch Barrettes- 2
  • Horizon Group USA Black & White Polka Dot Grosgrain Ribbon
  • Horizon Group USA Orange & Black Polka Dot Grosgrain Ribbon
  • Horizon Group USA Black & Orange Striped Grosgrain Ribbon

Cost of each project will vary depending on materials used.

Due to the seasonal nature of some merchandise, actual availability of some products pictured may vary.
 
     Candy Corn Barrette:
 
     Cut 1 (8 inch) piece of Yellow Candy Corn ribbon. Fold ends in toward the middle and glue, making a figure eight.
 
     Cut 1 (6 1/2 inch) piece of Yellow Candy Corn ribbon. Repeat step above. Glue smaller bow on top of large bow.
 
     Cut 1 (5 inch) piece of Yw/Org stripe ribbon. Make a figure eight, following above steps. Glue on top of the two candy corn bows.
 
     Cut 1 (2 inch) piece of Yellow Candy Corn ribbon. Wrap ribbon around the assembled ribbon bows and glue on back. Make sure a candy corn is centered in the ribbon.
 
     Cut 2 (5 inch) strips of Yellow Candy Corn ribbon to make the tails of the bow. Glue down the tails onto the barrette. Center the figure eights over the tails on the barrette and glue down.
 
     Black and Orange Barrette:
 
     Cut 1 (9 inch) piece of Blk/Org duality ribbon. Fold ends in toward the middle and glue, making a figure eight. Make sure black side of ribbon is facing up when folding.
 
     Cut 1 (7 ˝ inch) piece of Blk/Org duality ribbon. Fold ends in toward the middle and glue, making a figure eight. Make sure orange side of ribbon is facing up when folding.
 
     Cut 1 (6 ˝ inch) piece Blk/Org duality ribbon. Fold ends in toward the middle and glue, making a figure eight. Make sure black side of ribbon is facing up when folding.
 
     Glue the three bows together, small on top of large.
 
     Cut 1 (2 inch) piece of Blk/Wht dot ribbon. Wrap ribbon around the center of the bows and glue.
 
     Glue bows to the barrette.
 
     Trick or Treat Barrette:
 
     Cut 1 (10 inch) piece of Blk/Org check ribbon. Fold ribbon ends in towards the middle and glue down in the center.
 
     Cut 1 (8 inch) piece Trick or Treat ribbon. Fold ribbon ends in towards the middle and glue down in the center. Make sure the words ‘Trick or Treat’ are centered.
 
     Place the small bow onto the large bow and glue down.
 
     Cut 1 (2 inch) piece Blk/Org stripe ribbon. Wrap ribbon around the center of the bows and glue. Make sure the word “OR” is centered in the middle of the bow.
 
     Glue down the bows to the barrette.
 
     Black, White and Orange Barrette:
 
     Cut 1 (8 inch) pieces of Blk/Wht dot ribbon. Fold ends of each ribbon in toward the middle and glue, making a figure eight.
 
     Cut 1 (5 ˝ inch) pieces of Org/Blk dot ribbon. Fold ends of each ribbon in toward the middle and glue, making a figure eight. Place the small bow on top of the large bow and attach using glue.
 
     Cut 1 (2 inch) piece of Blk/Org stripe ribbon. Wrap around the center of the assembled bows and glue.
 
     Glue assembled bows to barrette. Repeat steps 1-4 for second barrette.
Tip: Refer to photo to complete project.

Follow manufacturer's directions for all products used.
 
The information on this instruction sheet is presented in good faith, but no warranty is given, nor results guaranteed. Quantities and selections may vary at each store. Michaels® Stores, Inc. disclaims all liability from any injury to anyone undertaking the construction of this project as a result of improper safety precautions. Since we have no control over physical conditions surrounding the application of information herein contained, MSI disclaims any liability for untoward results. © 2009 MSI.
  Add to My Michaels   Printer friendly version   Email to friend   Rate this project   More like this project